Pulse Plating Rectifiers
Sol Rectifiers PHFSPD P
Programmable High Frequency Switching Power Devices
Description
Our polarity reversing pulse plating rectifiers are reasonably priced, provided with 3 wave form output as standard features suitable for the most demanding electroplating requirements:
Anodizing
Brush plating
Electrocoagulation
Electrodegreasing
Electroetching
Electroforming
Electrophoresis
Electroplating
Electropolishing
Electrowinning
Intuitive LCD Interface
![plating rectifier interface, electroplating rectifier interface, programmable plating rectifier interface, programmable electroplating rectifier interface](https://www.solutionomics.com/wp-content/uploads/2024/04/plating-rectifier-interface-constant-soft-start-soft-stop-901x512-1.png)
Technology
IGBT programmable high frequency switching power device
DC Smoothed Wave Output
Low ripple smoothed wave pulse plating rectifiers suitable for the most stringent electroplating requirements including single metal, complex multi metal, decorative and hard chrome depositions
Standard Features
CONST – Constant smoothed wave output
HL P – High low pulse wave output
SW – Sine wave output
PLC communication port RTU RS485
Optional Features
PLC analog signal communication port N/A
Other Available Rectifier Models
Compact Bench Top Polarity Reversing Pulse Plating Rectifiers
![plating rectifier, electroplating rectifier, programmable plating rectifier, programmable electroplating rectifier](https://www.solutionomics.com/wp-content/uploads/2023/09/plating-rectifier-1700x1350-1-1024x813.jpg)
Volt Output Range
Standard unit 0~12 V
Other output on request
Ampere Output Range
Remote Control Bench Top Polarity Reversing Pulse Plating Rectifiers
![plating rectifier controller, electroplating rectifier controller, programmable plating rectifier controller, programmable electroplating rectifier controller](https://www.solutionomics.com/wp-content/uploads/2023/09/plating-rectifier-controller-1020x675-1.png)
![plating rectifier, electroplating rectifier, programmable plating rectifier, programmable electroplating rectifier](https://www.solutionomics.com/wp-content/uploads/2022/03/plating-rectifier-900x360-1.png)
Volt Output Range
Standard unit 0~12 V
Other output on request
Ampere Output Range
CONST – Constant Smoothed Wave Output
![plating rectifier interface, electroplating rectifier interface, programmable plating rectifier interface, programmable electroplating rectifier interface](https://www.solutionomics.com/wp-content/uploads/2024/04/plating-rectifier-interface-constant-1003x566-1.png)
Mode CV or CC
Output V or A
Timer for soft start
Timer for soft stop
Timer for auto cut-off
CV/CC
0 to unit rated output
0 to 9999 S
0 to 9999 S
0 to 9999 S/M/H
SW – Sine Wave Output
![plating rectifier interface, electroplating rectifier interface, programmable plating rectifier interface, programmable electroplating rectifier interface](https://www.solutionomics.com/wp-content/uploads/2024/04/plating-rectifier-interface-sine-wave-901x512-1.png)
Mode CV or CC
Upper output V or A
Lower output V or A
Timer for soft start
Timer for soft stop
Timer for half wave
Timer for auto cut-off
CV/CC
0 to unit rated output
0 to unit rated output
0 to 9999 S
0 to 9999 S
*5 to 150 Hz
0 to 9999 S/M/H
*Unit will display conversion of Hz to time in mS.
HL P – High Low Pulse Wave Output
![plating rectifier interface, electroplating rectifier interface, programmable plating rectifier interface, programmable electroplating rectifier interface](https://www.solutionomics.com/wp-content/uploads/2024/04/plating-rectifier-interface-h-l-pulse-1004x570-1.png)
Mode CV or CC
High output V or A
Low output V or A
Timer for soft start
Timer for soft stop
Timer for pulse on
Timer for pulse off
Timer for auto cut-off
CV/CC
0 to unit rated output
0 to unit rated output
0 to 9999 S
0 to 9999 S
*1.0 to 999.9 mS
*1.0 to 999.9 mS
0 to 9999 S/M/H
*Minimum increases with higher output units
12 V 3 – 100 A 1.0 to 999.9 mS, 12 V 150 – 300 A 2.0 to 999.9 mS, 12 V 500 A 5.0 to 999.9 mS, 12 V 600 – 1000 A 8.0 to 999.9 mS
Simple Operation
Sol Rectifiers PHFSPD P
These are programmable closed loop self-regulating units, which output can be set from 0 V to unit rated V output or from 0 A to unit rated A output.
With the intuitive control panel, operator can easily navigate through the pre-sets requirements for each wave output.
The moment operator presses the Start key the unit will automatically maintain the pre-set output value no matter any fluctuations in the plating cell resistance or in the main electrical supply to the unit for absolute plating consistency and precise control.
Durability & Care Free Operation
Relying on our state of the art electronic protection circuitry, our units are known to operate trouble free for years on and into decades.
When units are placed in a clean fresh air environment, care free operation can be expected. Only minimal air fan cleaning may be required once or twice a year.
Order Quantity & Shipping Options
Single order unit are welcomed.
We ship straight from the factory to any parts of the world.
Depending on order weight or volume the following shipping services are available:
Speed courier
Air freight
Air freight door-to-door
Sea freight
Sea freight door-to-door
Worldwide Customers
We have a large number of satisfied customers using on a daily basis our plating rectifiers in various countries, to name a few:
Australia, Austria, China, Denmark, Indonesia, Malaysia, Philippines, New Zealand, Singapore, South Africa, Thailand, United Kingdom of Great Britain, United State of America, Vietnam, etc.
Specifications
IGBT programmable high frequency switching power device.
Automatic cut-off protection against output over voltage, over current and overheating.
Automatic cut-off protection against AC input over or under voltage and phase distribution imbalance.
Low ripple DC smoothed wave output.
Closed loop self-regulating CV or CC operation.
Precise voltage and current regulation.
Fast response to AC input and DC output variations.
Insensitive to AC input phase sequence.
Large LCD display.
Reliable, durable and simple to operate.
Low electrical consumption.
Small in size and lightweight.
For units with remote controller, the power console can be placed away from the plating tank, hence away from corrosive splashes and fumes and the remote controller close to the plating tank for operator convenience.
The following options are available on request:
1) PLC analog signal communication port: N/A
220 V Single Phase 50/60 Hz input for units 300 A output and below.
220 / 380 / 400 / 415 / 440 / 480 V 3 Phase 50/60 Hz input for units 500 A output and above.